3G-Modding your eee 1000he hackintosh

  • March 14, 2010
Table of Contents

As some of you may know I’ve been using snow leopard on my eee 1000he for quite a while(You can still get the modded DSDT I use on my system from my github page)

Here’s a list of items I got myself:

  • a sim card(yeah, you’ll laugh, I actually forgot about this part… :P)
  • a 3G minipci card. i used an Option 378 which is quite cheap. I will explain later… Some people use a sierra wireless mc8775
  • a minipci socket, for example this one from farnell
  • a sim slot 8 pin

I won’t cover the details on soldering the sim and minipci socket as it’s explained on the eeepc user forum

A word of advice before trying to solder the sockets onto the board. You might wanna scrape of the surface of the solder pads on the mainboard first, as that will make it easier for you.

As described on the forum post you’ll need to short the 3.3V line the USB lines and a fourth one for powering up the minipci socket aside from soldering the sim slot.

The images below are a courtesy of dementho from the eee forums:




The real issue arose when I actually tried to initialize the card in MacOS. Turns out the Option cards start in ZeroCD mode and need to be initialized in modem mode prior to be usable. Well, normally you would just install the driver and be done with it but not so with normal unlocked GTM378 cards you buy on ebay.

y GTM378 card came with an old firmware. So the vendor id was 0x5c6(qualcomm) and product id 0x1000, whereas the vendorId should be 0x0af0(Option NV). Naturally the Globesurfer 7.2 osx drivers don’t work with this device. Not even if you hardcode the product and device id into the drivers plists.

The solution is to debrand your GTM378 by finding the superfire firmware of any GTM378 card and patching it to accept your card as target. That is Globesurfer ICON 7.2 and a whole bunch of others. The firmware I have here is 2.5.11hD I think.

Enable logging in the updater:

 8.144: CPagePreparation::Do, Zaltys detected properly
14.618: CPagePreparation::Do, product:  GlobeSurfer ICON 7.2 E.
14.618: CPagePreparation::Do, code:  MO0201-10959.
14.618: CPagePreparation::Do: unsupported card (MO0201-10959).

O0201-10959 is your target. search for

5400610068006f006d0061

which is essentially Tahoma in hex. The second occurance should lead you to your target. See below:

Open the installer in a hex editor and write your card id in the installer. I uploaded the firmware here. That should allow you to upgrade your card without problems. After that you can download the snow leopard drivers from the ICON 225 support page

Ironically they work fine with the GTM378 and fix a lot of issues the GTM378 and ICON 7.2 drivers have(since they’re essentially the same just newer).

HTH

… as for me, I’m enjoying the 3g mod on my hackintosh!

comments powered by Disqus

Related Posts

Vim & Rails

I did a little write up on my general vim workflow and presented it at the hamburg rails user group meeting . I didn’t quite manage to get it as smooth as I originally planned, but anyway you can find the slides here

Read More

awesome with gentoo-prefix

I just updated a whole bunch of ebuilds for gentoo-prefix you can find the overlay here.

Just clone it and put it somewhere in your $EPREFIX/usr/local/portage then add that folder to your make.conf

Read More

A minimalistic rfkill gtk gui for toggling your bluetooth and wireless

I just wrote a little rfkill frontend with gtk+. If you use an acer laptop you should load acer-wmi, make sure you have acpi_osi=Linux in your kernel boot.

Read More